Heavy Duty Driveline Service Kit
Click To Enlarge

Heavy Duty Driveline Service Kit with TruckFaultCodes.com

Price: $735.00
  • Item #: 20175
  • Manufacturer's Product Number: 20175
* Marked fields are required.
Qty: *

Features two of our most popular tools for servicing heavy duty drivelines.

Kit includes:

  • 10102 Heavy Duty Universal Joint Puller
  • 10803 Heavy Duty Yoke Puller

U-Joint Puller: 10102

CAUTION: Failure to check the spherical thrust washer and replace as necessary may result in unrepairable damage to your U-Joint Puller glove casting. Preventative maintenance as outlined above will ensure many years of use from your Tiger Tool puller.

Failure to perform preventative maintenance will void your warranty.

  1. Remove all fasteners from bearing cups.
  2. Slip the U-Joint Puller over the yoke of the drive line.
  3. Turn the tool’s forcing screw clockwise with either an air or hand wrench. (Note: reverse thread)
  4. Once bearing cup has been removed, repeat the process on the remaining bearing cups.

The 10102 U-Joint Puller may be used with up to a 1” impact wrench without voiding warranty.

Preventative Maintenance Keep forcing screw clean and lubricated at all times. Failure to maintain the spherical thrust washer located inside the glove will result in excessive wear to the part. Check and lubricate this part (lubricate load bearing surface in glove, under cap, on both sides of spherical washer) periodically and replace as necessary.

Contact your Dealer or Tiger Tool for replacement washers. (We recommend SAE 30 lube for the threads and EP ‘with molly grease’).

 Yoke Puller: 10803

Use any quality oil on forcing screw. 

Half Round Yoke

  1. Remove the large nut and washer that retains yoke to shaft.
  2. Apply penetrating lubricant to splines of the shaft, wing cap bolt holes, and forcing screw of tool.
  3. Thread the forcing screw into the pull bar until threads begin to show through the other side.
  4. Hold pull bar assembly by the forcing screw and position the tool onto the yoke. Note: pull bar end reliefs should face yoke.
  5. Attach the adaptor cap by four bolts and then tighten down both caps.
  6. Hand tighten the forcing screw until the center point aligns with the shaft center.
  7. Using up to a 3⁄4" impact wrench, begin applying power to the forcing screw.
  8. Continue turning the forcing screw until yoke is completely remove

Full Round Yoke

  1. Remove the large nut and washer retaining yoke to shaft.
  2. Apply penetrating lubricant to splines of the shaft and forcing screw of the tool.
  3. With the pull bar separated from the forcing screw, slide the bar through bearing cup bores until centered.
  4. Thread the forcing screw into pull bar until it contacts the shaft.
  5. Using up to a 3⁄4" impact wrench, begin applying power to the forcing screw.
  6. Continue turning the forcing screw until the yoke is completely removed.

BONUS: Includes TruckFaultCodes.com

Exclusively only available through DieselLaptops.com, we offer every customer purchasing TigerTool a free 12-month subscription to www.TruckFaultCodes.com. This website will give you repair information on every single diagnostic code that exists. This covers all diesel trucks, from Cummins with Dodge engines all the way up to your normal commercial trucks such as Freightliner, Peterbilt, Volvo, and all the rest of them Coverage includes all the truck components such as engine, transmissions, ABS, cab, chassis, and more. You can also view more on the TruckFaultCodes.com website.

Warranty

With all the care, craftsmanship and attention to detail that goes into every Tiger Tool product, you can be sure you’re choosing a product that’s built to last and engineered to perform. Tiger Tool offers a Limited Lifetime Warranty on castings, two years on machined or threaded parts and one year warranty on hydraulic components. You can read more about Tiger Tool on our Blog page.

Reviews (0) Write a Review
No Reviews. Write a Review